Εγχειρίδιο Canon EF-M 18-55mm f/3.5-5.6 IS STM

Canon EF-M 18-55mm f/3.5-5.6 IS STM

Στα δεξιά μπορείτε να βρείτε το εγχειρίδιο Canon EF-M 18-55mm f/3.5-5.6 IS STM. Αν έχετε κάποιες ερωτήσεις σχετικά με το παρακαλούμε επιτρέψτε μας το γνωρίζουμε στο τέλος αυτής σελίδας.

Μάρκα
Canon
Μοντέλο
EF-M 18-55mm f/3.5-5.6 IS STM
Προϊόν
EAN
4960999819631
Γλώσσα
Αγγλικά
Τύπος αρχείου
PDF
Ιστότοπος
http://www.canon.com/
ENG-1
Wide end
Telephoto end
Zoom ring
ENG
EF-M LENS Instructions
EF-M18-55mm f/3.5-5.6 IS STM
Nomenclature
Focusing ring
Hood mount
Filter Mounting Thread
Lens mount index
Contacts
Zoom position index
Zoom ring
Thank you for purchasing a Canon product.
The Canon EF-M18-55mm f/3.5-5.6 IS STM lens is a 3x
standard zoom lens developed for interchangeable-lens digital
cameras compatible with EF-M lenses*.
* Only the following cameras are compatible with EF-M lenses (as
of July 2012):
EOS M
"IS" stands for Image Stabilizer.
"STM" stands for stepping motor.
Safety Precautions
Do not look at the sun or a bright light source through the
lens. Doing so could result in vision loss or blindness.
Whether it is attached to the camera or not, do not leave
the lens under the sun without the lens cap attached. This
is to prevent the lens from concentrating the sun’s rays, which
could cause a fire.
Handling Cautions
If the lens is taken from a cold environment into a warm
one, condensation may develop on the lens surface and
internal parts. To prevent condensation in this case, first
put the lens into an airtight plastic bag before taking it from a
cold to warm environment. Then take out the lens after it has
warmed gradually. Do the same when taking the lens from a
warm environment into a cold one.
Do not leave the lens in excessive heat such as in a car in
direct sunlight. High temperatures can cause the lens to
malfunction.
Please also refer to the handling cautions found in your
camera’s instructions.
Conventions used in this instruction
Warning to prevent lens or camera malfunction or
damage.
Supplementary notes on using the lens and taking
pictures.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Do not make any changes or modifications to the equipment unless
otherwise specified in the instructions. If such changes or modifications
should be made, you could be required to stop operation of the
equipment.
This equipment has been tested and found to comply with the limits for
a class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
1. Mounting and Detaching the Lens
See your camera’s instructions for details on mounting and
detaching the lens.
After detaching the lens, place the lens with the rear end
up to prevent the lens surface and contacts from getting
scratched. (fig.)
If the contacts get soiled, scratched, or have fingerprints on
them, corrosion or faulty connections can result. The camera
and lens may not operate properly.
If the contacts get soiled or have fingerprints on them, clean
them with a soft cloth.
If you remove the lens, cover it with the dust cap. To attach
it properly, align the lens mount index and the index of the
dust cap as shown in the diagram, and turn clockwise. (fig.)
To remove it, reverse the order.
2. Zooming
Turn the lens’ zoom ring to adjust the size of the photo field or
subject. (fig.)
For wide shots, turn the zoom ring toward the wide end.
For close-ups, turn the zoom ring toward the telephoto end.
Be sure to finish zooming before focusing. Zooming after
focusing can affect the focus.
Blurring may temporarily occur if the zoom ring is quickly
rotated.
Zooming during still image exposure will result in delayed
focus. This causes any streaks of light that are captured
during exposure to be blurred.
3. Manual Focus
When the camera’s focus mode is set to [MF], focus manually by
turning the focusing ring (fig.).
Quickly rotating the focusing ring may result in delayed focus.
Focus mode is set using the camera. Please refer to the
camera’s instructions.
After autofocusing in [AF+MF] mode, focus manually by
pressing the shutter button halfway and turning the focusing
ring (full-time manual focusing).
4. Image Stabilizer
This lens is equipped with an Image Stabilizer. This function
corrects camera shake, allowing users to capture sharp images.
Also, the Image Stabilizer automatically provides optimal image
stabilization depending on shooting conditions (such as shooting
still subjects and following shots). Please set the Image Stabilizer
ON or OFF using the camera settings. See your camera’s
instructions for details.
The Image Stabilizer cannot compensate for a blurred shot
caused by a subject that moved.
The Image Stabilizer may not be fully effective if you shoot
from a violently shaking vehicle or other transportation.
The Image Stabilizer consumes more power than normal
shooting, so fewer shots can be taken if you use the
function.
When shooting a still subject, it compensates for camera
shake in all directions.
It compensates for vertical camera shake during following
shots in a horizontal direction, and compensates for
horizontal camera shake during following shots in a vertical
direction.
When you use a tripod, the Image Stabilizer should be
turned off to save battery power.
Even with a monopod, the Image Stabilizer will be as
effective as during hand-held shooting.
However, depending on the shooting environment, the
Image Stabilizer effect may be less effective.
■ Dynamic IS Function (Movie shooting only)
The EF-M18-55mm f/3.5-5.6 IS STM is equipped with dynamic IS,
effective when shooting while walking since it expands the IS range.
Achieves effective IS at the wide end.
Automatically activates when the camera is set to Movie
Shooting.
CT1-8583-001
COPY

Έχετε κάποια ερώτηση σχετικά με Canon EF-M 18-55mm f/3.5-5.6 IS STM;

don't hesitate to ask. Make sure to describe your problem clearly

Αγοράστε σχετικά προϊόντα:

Προδιαγραφές προϊόντων

Σύστημα Φακών
Τύπος φακού Ευρύς φακός ζουμ
Εξάρτημα για -
Διάρθρωση φακού 13/11
Προσαρμογή εστίασης Αυτοκίνητο
Εστιακή απόσταση 18 - 55 mm
Αριθμός λεπίδων διαφράγματος 7
Μέγιστη οπή 38
Ελάχιστη απόσταση εστίασης 0.25 m
Ελάχιστη οπή 22
Αντίστοιχο φακού 35 χιλιοστά φωτογραφικής μηχανής 29 - 88 mm
Σταθεροποιητής εικόνας yes
Γωνία θέασης, οριζόντια 64 °
Γωνία θέασης, κατακόρυφη 23 °
Τύπος ζουμ Στροφή
Μορφή αισθητήρα εικόνας APS-C
Διαγώνια γωνία θέασης (ελάχ.) 27 °
Διαγώνια γωνία θέασης (μέγ.) 74 °
Αριθμός στάσεων σταθεροποιητή εικόνας 4
Διεπαφή σύνδεσης φακού Canon EF-M
Βάρος και διαστάσεις
Διάμετρος 60.9 mm
Μήκος 61 mm
Μέγεθος φίλτρου 52 mm
Βάρος 210 g
Σχέδιο
Υλικό Αλουμίνιο (Αργύλιο)
Χρώμα προϊόντος Μαύρος (Μαύρο)
Απόδοση
Ενεργοποιητής AF STM
Συμβατότητα -
Συμβατότητα με μοντέλα φωτογραφικών μηχανών Canon
Μέγιστη μεγέθυνση 0.25 x
Κάλυμμα φακού yes

Σχετικά προϊόντα: